CVS – Sıkça Sorulan Sorular
Seyreltme Titrasyonu Problemleri (suppressor tayini)
MLAT/LAT (parlaklaştırıcı tayini) problemleri
Response Curve Problemleri (leveler tayini)
Ölçüm problemleri
FAQ
The electrode test is failing.// Ölçümle ilgili sorunlar
FAQ
The measurement curves are noisy.// Ölçümle ilgili sorunlar
FAQ
Conditioning is taking a long time.// Ölçümle ilgili sorunlar
FAQ
The measured values are widely scattered.// Ölçümle ilgili sorunlar
FAQ
The peak is no longer recognized.// Ölçümle ilgili sorunlar
FAQ
The signal is not decreasing despite suppressor addition.// Ölçümle ilgili sorunlar
FAQ
The measuring signal for the VMS is fluctuating.// Ölçümle ilgili sorunlar
FAQ
Are CVS measurements temperature-dependent?// Ölçümle ilgili sorunlar
FAQ
Is it possible to repair a defective driving axle (6.1204.x010 or 6.1204.x20)?// Ölçümle ilgili sorunlar
Donanım problemleri
FAQ
The peristaltic pump on the sample changer is not transferring the entire sample to the measuring vessel.// Donanımla ilgili sorunlar
FAQ
The status LED of the 800 Dosino is flashing quickly and the dosing unit is not being recognized.// Donanımla ilgili sorunlar
FAQ
I am getting an error message that the dosing unit data cannot be read.// Donanımla ilgili sorunlar
FAQ
An electrode connector on the electrode cable is broken.// Donanımla ilgili sorunlar
FAQ
Solution is leaking between the 894 Professional CVS and the measuring head.// Donanımla ilgili sorunlar
FAQ
The dosing unit is blocked and/or leaking.// Donanımla ilgili sorunlar
FAQ
The membrane pumps of the 843 Pump Station are not operating at full pump capacity.// Donanımla ilgili sorunlar
FAQ
I am getting an error message. The 800 Dosino cannot be actuated by the 894 Professional CVS.// Donanımla ilgili sorunlar
Genel problemler
FAQ
At what intervals should a dosing unit be cleaned?// Genel sorunlar
FAQ
The measurement curves are noisy. What is the reason for that?// Genel sorunlar
FAQ
How often should the dosing units be prepared?// Genel sorunlar
FAQ
How should the additives be stored?// Genel sorunlar
FAQ
How should the electrodes be stored?// Genel sorunlar
FAQ
What preparatory steps need to be taken before shutting down the measuring system?// Genel sorunlar
FAQ
The measuring signal in VMS is exceptionally small and conditioning in VMS is taking a long time. What is the reason for that?// Genel sorunlar
FAQ
How frequently do the electrodes need to be conditioned?// Genel sorunlar
FAQ
Can measurements made using other software be used in viva?// Genel sorunlar
FAQ
Preparing the Dosinos is taking a long time. Is it possible to speed up this step?// Genel sorunlar
Döner disk elektrod
FAQ
How temperature-resistant is the platinum electrode tip?// Dönen disk elektrod
FAQ
Can platinum electrode tips be polished// Döner Disk Elektrotlarının Bakımı// Dönen disk elektrod
FAQ
The electrode surface of the platinum electrode tip is coated with a foreign metal (Cu, Sn, etc.). What can I do?// Döner Disk Elektrotlarının Bakımı// Dönen disk elektrod
FAQ
Can Metrohm polish platinum electrode tips?// Döner Disk Elektrotlarının Bakımı// Dönen disk elektrod
FAQ
Can the platinum electrode tip be treated in an ultrasonic bath?// Döner Disk Elektrotlarının Bakımı// Dönen disk elektrod
FAQ
How do I clean my platinum electrode tip?// Döner Disk Elektrotlarının Bakımı// Dönen disk elektrod
FAQ
Does the Pt RDE diameter affect my analysis results?// Dönen disk elektrod
Referans elektrot
FAQ
Until now, I have always used diluted H2SO4 as a bridge electrolyte. Can I use another electrolyte instead of KNO3?// Referans elektrotlarının bakımı// Referans elektrod
FAQ
My reference electrode has dried out. Can I regenerate it again?// Referans elektrotlarının bakımı// Referans elektrod// Referans elektrod// Referans elektrotlarının bakımı
FAQ
How often do I need to change the reference electrolyte?// Referans elektrotlarının bakımı// Referans elektrod
FAQ
How often does the bridge electrolyte need changing?// Referans elektrotlarının bakımı// Referans elektrod
Yardımcı elektrot
FAQ
The electrode surface of the auxiliary electrode is coated with a foreign metal (Cu, Sn, etc.). What can I do?// Yardımcı elektrotların bakımı// Yardımcı elektrod
FAQ
Is polishing the platinum pin of the auxiliary electrode allowed?// Yardımcı elektrotların bakımı// Yardımcı elektrod