Application Finder

Citric acid and oxalic acid are present in many products, such as foods or chemical solvents (e.g., decontamination solutions). Both acids are reducing agents and citric acid is additionally a powerful antioxidant. Due to their mutual impact (buffer effect), a content calculation is only possible with correction factors for each acid. A fast and accurate determination by potentiometric titration using the dEcotrode plus and sodium hydroxide as titrant can be realized in this Application Note.

Determination of the bromine index in low-level standards by bivoltametric titration with bromide/bromate using a double Pt electrode.

Determination of acetate, chloride, and phosphate in an infusion solution by potentiometric titration with sodium hydroxide after conversion of the anions to the corresponding acids.

Determination of the soap content of soap noodles by potentiometric titration with TEGO®trant A100 using the «Ionic Surfactant» electrode.

Determination of soaps and anionic surfactants in washing powder by potentiometric two-phase titration with TEGO®trant A100 using the «Surfactrode Resistant» electrode.

Determination of anionic surfactants in shower oil by potentiometric two-phase titration with TEGO®trant A100 using the «Surfactrode Resistant» electrode.

Determination of cationic surfactants in a household cleaner by potentiometric two-phase titration with sodium dodecylsulfate using the «Surfactrode Resistant» electrode.

This application note describes the determination of nonylphenol ethoxylate by potentiometric titration with sodium tetraphenylborate using the NIO surfactant electrode.

Due to its price and wide availability, the anionic surfactant sodium lauryl sulfate (SLS; SDS) can be found in many detergents as an emulsifier or as a fat solvent e.g., in cleaning or cosmetic products. To avoid causing severe dry skin and hair, and thus skin irritation, regulations in many countries have restricted the sodium lauryl sulfate concentration in ready-to-use products to a range between 0.05–2.5% SLS. To control the concentration of SLS in different products, a titration is carried out with TEGO® trant A100 and the Optrode. The evaluation is done automatically by means of a software, leading to reliable and reproducible results.

Determination of lauryl ether sulfate (LAES) by potentiometric/turbidimetric titration with TEGO®trant A100 using the 610 nm Spectrode.

Determination of calcium in aqueous solutions by photometric titration with EDTA using the 610 nm Spectrode.

Determination of the sum of calcium and magnesium in cement by photometric titration with EDTA using the 610 nm Spectrode.

Determination of aluminum in cement by photometric back-titration of the EDTA excess with zinc sulfate using the 610 nm Spectrode.

Determination of traces of calcium in brine by photometric titration with 1,2-diaminocyclohexanetetraacetic acid using the 610 nm Spectrode.

Determination of nitrite in aqueous solutions by potentiometric back-titration of the added permanganate excess with ammonium iron(II) sulfate using the Pt-Titrode.

Determination of citrate in mineral water drinks by potentiometric titration with copper sulfate using the Cu-ISE. Before the determination, the sample is degassed and passed through a cation-exchange resin.

Simultaneous determination of titanium and iron by potentiometric titration with potassium dichromate using a platinum electrode. Before determination, Ti4+ and Fe3+ are reduced with Cr2+.

Determination of the antihistamine astemizole in raw products by nonaqueous potentiometric titration with perchloric acid using separate electrodes.

Determination of calcium in cheese by potentiometric titration with EGTA using the Cu-ISE.

Tallow amine ethoxylates are toxic to aquatic life, and therefore their use is restricted. This Application Note explains an approach to determine these non-ionic surfactants potentiometrically.

This application note shows how coconut oil ethoxylates can be determined via potentiometric titration.

Determination of iron and nickel in binary mixtures by potentiometric titration with EDTA at different pH values using the Cu-ISE.

Determination of calcium pantothenate by nonaqueous potentiometric titration with perchloric acid using separate electrodes.

Determination of palladium(II) by potentiometric titration with hexadecylpyridinium chloride using the «Ionic Surfactant» electrode.

Determination of reducing sugars in wine and candies according to Fehlings method by potentiometric/iodometric titration using the Pt-Titrode.

The automated system Basic water analysis determines conductivity, pH value, and alkalinity in all kind of water samples. The high degree of automation (e.g., automated sample addition, automated calibration as well as automated titer and cell constant determination) minimizes errors and guarantees an outstanding reproducibility.

In this application note, a fully automated system is presented which allows the determination of several parameters according to various standards within one analysis. These include conductivity (ISO 7888, EN 27888, ASTM D1125, EPA 120.1), the pH value (EN ISO 10523, ASTM D1293, EPA 150.1), alkalinity (EN ISO 9963, ASTM D1067, EPA 310.1), and Ca/Mg content (ISO 6059, ASTM D1126, EPA 130.2). Additionally, the system transfers the required sample volume into an external titration vessel for the analysis, reducing manual sample preparation. Furthermore, all sensors can be automatically calibrated and the titer of each titrant can also be determined.

In this application note, a fully automated system is presented which allows the determination of several parameters according to various standards within one analysis. These include conductivity (ISO 7888, EN 27888, ASTM D1125, EPA 120.1), pH value (EN ISO 10523, ASTM D1293, EPA 150.1), alkalinity (EN ISO 9963, ASTM D1067, EPA 310.1), and chloride content (ISO 9297, ASTM D512, EPA 325.3). Additionally the system transfers the required volume of sample into an external titration vessel, further reducing manual sample preparation. Furthermore, all sensors can be calibrated automatically and the titer of each titrant can also be determined.

In this application note, a fully automated system is presented which allows the determination of several parameters according to various standards within one analysis. These include conductivity (ISO 7888, EN 27888, ASTM D1125, EPA 120.1), pH value (EN ISO 10523, ASTM D1293, EPA 150.1), alkalinity (EN ISO 9963, ASTM D1067, EPA 310.1), Ca/Mg (ISO 6059, ASTM D1126, EPA 130.2), and chloride (ISO 9297, ASTM D512, EPA 325.3). Additionally the system transfers the required volume of sample into external titration vessels for the different analyses, reducing manual sample preparation. Furthermore, all sensors can be automatically calibrated and the titer of each titrant can also be determined.

This Application Note describes the photometric determination of sulfate in aqueous solutions using the Optrode (520 nm). Sulfate is precipitated with an excess of barium chloride solution. Excess barium is subsequently titrated with EDTA.

This Application Note describes the photometric determination of aluminum in cement using the Optrode (574 nm). Following breakdown of the cement sample, the dissolved aluminum is titrated with EDTA. The excess EDTA is titrated back with zinc sulfate solution.

This Application Note covers the photometric determination of calcium in cement using the Optrode (610 nm). After digestion of the cement sample, calcium is titrated with EDTA to the murexide endpoint.

This Application Note describes the digestion of a cement sample and the photometric determination of iron in accordance with DIN EN 196-2 by means of Optrode at 610 nm. Sulfosalicylic acid is used as the indicator and EDTA as the titrant for the determination.

This Application Note is devoted to the photometric determination of magnesium in cement using the Optrode (610 nm). After digestion of a sample aliquot, the magnesium content is determined using EDTA titration.

This Application Note treats the photometric titration of nickel using the Optrode (520 nm). Murexide was used as the indicator and EDTA as the titrant.

This Application Note details the photometric determination of chondroitin sulfate with 1-hexadecylpyridinium chloride as titrant and with the Optrode (660 nm). The method is in compliance with the Ph. Eur. and the USP.

ASTM D8192 describes the photometric titration of the total hardness, calcium hardness, and magnesium hardness in water with an optical sensor for objective endpoint indication, increasing precision and reliability. The method is suitable for both colored and colorless samples such as groundwater, surface water, wastewater, and drinking water. Using a fully automated OMNIS system equipped with an Optrode ensures that the sample preparation and analysis are repeatable.

This Application Note describes the photometric determination of sulfate using the Optrode (610 nm). Sulfate is titrated with a lead nitrate solution; dithizone is used as indicator.

Vitamin C, also known as ascorbic acid or L-ascorbic acid, is an essential nutrient involved in the repair of tissues and the enzymatic production of certain neurotransmitters. It is required for the functioning of several enzymes and immune performance, and is also an important antioxidant. This nutrient is found in many foods and is often used as a dietary supplement.This Application Note describes the photometric determination of ascorbic acid according to the standard ISO 6557-2. To increase the objectivity on the determined equivalence point and the reproducibility of the results, an autotitrator equipped with a photometric sensor, the Optrode, is used. The titrant 2,6-Dichlorophenol-indophenol (DCIP or DPIP) simultaneously serves as titrant and indicator.

The carboxyl end groups (CEG) in polymers, such as polyethylene terephthalate (PET), are a measure of the number of unreacted carboxylic acid groups at each end of a polymer chain. The number of CEGs may influence the hydrolysis resistance of geosynthetics, such as geogrids and geotextiles. The lower the CEG value the higher is the hydrolysis resistance of geosynthetics, which in turn increases their stability.This Application Note describes the photometric titration of carboxyl end groups in PET pellets using the Metrohm Optrode. The acidic end groups of the polymer are titrated with an ethanolic KOH solution using bromophenol blue as indicator.

This Application Note describes the photometric determination of bismuth nitrate using the Optrode (520 nm). The sample is titrated with EDTA solution past the endpoint; xylene-orange is used as the indicator. The method for bismuth nitrate fulfills the directives defined in the Ph. Eur. and the USP.

This Application Note looks at the photometric determination of manganese sulfate using the Optrode (610 nm). Manganese is titrated with EDTA; Eriochrome Black T is used as indicator. The method complies with Ph. Eur. and the USP.

This Application Note describes the photometric determination of zinc sulfate using the Optrode at a wavelength of 610 nm. Complexometric titration of zinc requires EDTA as titrant and Eriochrome Black T as indicator. The method fully complies with Ph. Eur. and USP.

This Application Note describes the determination of total content of Ba, Ca, Mg, Pb and Zn in unused lubricating oil by means of the Optrode (610 nm). An excess of EDTA is first added to the metals. Afterwards, the excess EDTA is titrated back with magnesium chloride solution up to the end point of the indicator Eriochrome Black T.

The acid number (AN) of insulating, transformer, and turbine oils is crucial to ensure safe operation, operating equipment control, and corrosion prevention. These oils generally have low AN specifications and their AN determination by manual color-indicator titration is difficult, especially when analyzing colored samples.Using a Titrator with a photometric sensor to detect the end point ensures that the titrations are always carried out under the same conditions. This greatly increases the precision and reliability of the results, which in turn results in improved monitoring for your operations.

Basic additives are added to petroleum products to inhibit corrosion as they have a neutralizing effect on acidic compounds, which are formed as a result of degradation processes. Total base number (TBN) indicates the amount of basic additives present and thus can be used as a measure for the degradation of the petroleum product.Using an automated titration system with a photometric sensor to detect the end point ensures that the titrations are always carried out under the same conditions. This improves the precision and reliability of the results.This Application Notes describes the fully automated photometric determination of TBN in used engine oil using the Metrohm Optrode for the indication of the methyl orange endpoint (at 520 nm).

The automated system MATi 13 determines the permanganate index in all kind of water samples according to EN ISO 8467. The high degree of automation (e.g., automated sample addition, automated titer and blank value determination) minimizes errors and guarantees robust and reproducible results.

Automated mixing of a suspension and a solvent in a 50 mL dosing unit can be used to add a well-defined amount of a suspension-solvent mixture to a sample solution without clogging the dosing unit and tubing by the undiluted suspension.The method is explained by means of the TAN determination of a petroleum sample using thermometric titration. For a better endpoint recognition, small amounts of a paraformaldehyde-solvent suspension are added (catalyzed endpoint thermometric titration).

Fresh as well as used petroleum products may contain acidic components as additives or degradation products. The acid number (AN) is a measure for the relative amount of acids present expressed as mg KOH per g sample. Moreover, AN is used as a quality parameter of lubricating oils both for assessing the quality of new formulations and as an indicator for the degradation of such formulations during service. The use of a pH electrode suitable for non-aqueous titrations ensures the reliable determination of the equivalence point. A flexible sleeve diaphragm facilitates its cleaning especially after use in heavily contaminated samples, such as in used engine oils. Using the correct electrode greatly increases the precision and reliability of the results. This Application Note describes the potentiometric determination of the acid number according to ASTM D664 and IP 177 using the pH electrode Solvotrode easyClean.

Basic chemicals are added to petroleum products to prevent corrosion as they neutralize acidic components that form during the use and aging of these products. The base number (BN) gives an indication regarding the amount of these basic additives present, and it can be used as a measure for the degradation of the petroleum product.This Application Note describes the potentiometric determination of the base number according to ISO 3771, ASTM D2896, and IP 276 using the Metrohm Solvotrode easyClean and a fully automated OMNIS system.