Application Finder

Perchlorate contamination in drinking water may have different sources. Besides natural deposits, anthropogenic sources like fertilizers and rocket fuel residue add to hazardous water contamination. Perchlorate interferes with iodine uptake into the thyroid gland. Newborns and children are particularly vulnerable, affected as thyroid hormones are essential for growth. Besides ion chromatography (IC) followed conductivity detection, IC hyphenated with an MS detector can be used to measure perchlorate down to sub-µg/L levels. In this application IC is hyphenated with a triple-quadrupole MS (IC-MS/MS) for perchlorate determination in order to meet the requirements of EPA 332.0. This IC-MS/MS setup avoids the possible interference of sulfate.

Chlorinating drinking water can form carcinogenic byproducts. EPA Method 557 enables µg/L-level quantification of haloacetic acids using Metrohm IC-MS/MS technology.

During drinking water disinfection with chlorine, chloramine, or ozone, potentially toxic halogenated byproducts can be formed. The disinfectants can react with naturally occurring bromide and/or organic matter in the source water and form one of the most common and highly toxic disinfection byproducts (DBPs): haloacetic acids (HAAs). To protect human health, maximum tolerable levels of HAA in drinking waters are regulated (EPA 816-F-09-004). The EPA Method 557 specifies the analysis of HAAs beside bromate and dalapon by ion chromatography coupled to tandem mass spectroscopy (IC-MS/MS) with LODs varying from 0.02–0.11 µg/L. However, even with single MS, a high sensitivity is achieved to determine the current MCLs within an adequate accuracy. This Application Note describes the analysis of bromate, chlorite, monochloroacetic acid (MCAA), monobromoacetic acid (MBAA), bromochloroacetic acid (BCAA), bromodichloroacetic acid (BDCAA), dibromoacetic acid (DBAA), dichloroacetic acid (DCAA), tribromoacetic acid (TBAA), chlorodibromoacetic acid (CDBAA), and trichloroacetic acid (TCAA) with IC/MS. The Metrohm Driver 2.1 for EmpowerTM offers the analysis as a single software solution with EmpowerTM.

Determination of chloride, nitrate, phosphate and sulfate in plant leaf extracts using anion chromatography with direct conductometric detection.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in an effluent sample using anion chromatography with direct conductometric detetction.

Determination of traces of nitrite, thiosulfate, and iodide using anion chromatography with amperometric detection at the carbon paste electrode.

Determination of perchlorate in process water using anion chromatography with direct conductivity detection.

Determination of chromate using anion chromatography with post-column reaction and UV/VIS detection.

Determination of silicate and borate and their limits of determination (LOD) and quantification (LOQ) according to the EPA procedure for method detection limit (MDL) using anion chromatography with direct conductivity detection and Metrohm Inline Calibration.

Determination of silicate in the presence of fluoride and its limits of determination (LOD) and quantification (LOQ) according to the EPA procedure for method detection limit (MDL) using anion chromatography with direct conductivity detection and Metrohm Inline Calibration.

Determination of sodium dodecylsulfate (SDS, sodium laurylsulfate) using anion chromatography with direct conductivity detection.

Determination of borate in a borate effluent using anion chromatography with direct conductivity detection.

Determination of chloride and sulfate in effluent after Metrohm Inline Dialysis using anion chromatography with direct conductivity detection.

Determination of sulfide in an effluent sample using anion chromatography with amperometric detection.

Silicate and borate contents determine the quality of drinking and irrigation water and have to be regularly analyzed. Especially in fresh water reclaimed from seawater, borate levels need to be controlled. This application shows the determination of silicate and borate besides some standard anions in drinking water using ion chromatography with direct conductivity detection.

Naphtha is the first petroleum product during the distillation process of crude oil or coal tar. It is primarily used as a base material for the production of gasoline or as a solvent. Accidental spills occur regularly at many locations throughout the world, leading to soil contamination.Investigation of contaminated sites is usually performed using gas chromatography, for which the soil sample has to be frozen, grinded, and subsequently extracted prior to the analysis. Using Visible-Near Infrared Spectroscopy such sample preparation steps are not necessary at all, making this method a viable, fast, and simple to use alternative.

Determination of boric acid and acetic acid in process water using ion-exclusion chromatography with conductivity detection after chemical suppression.

Determination of borate in seawater using ion-exclusion chromatography with suppressed conductivity detection after inline matrix elimination.

The human daily intake of boron from food and beverages is approximately 2 mg. This is far below any toxic level. Some plants, however, are extremely sensitive to boron concentrations above 1 mg/L, e.g., strawberries, blackberries. As seawater contains 4 to 5.5 mg/L of boron, desalination is required to remove surplus boron besides other ions. This application shows the determination of boron (as borate) by ion-exclusion chromatography with conductivity detection after inverse suppression. The method has been optimized to get a sufficient fluoride/borate separation.

Determination of polysaccharides (n glucose units) in a plant extract using pulsed amperometric detection and a high-pressure gradient.

The determination of cyanide and sulfide in the trace range requires an alkali eluent and amperometric detection. This Application Note describes a new column/eluent combination for optimized separation. The combination consists of the Metrosep A Supp 10 - 100/2.0 Microbore Column and a sodium hydroxide eluent that contains traces of EDTA for the complexation of the transition metals. This yields a better peak shape and detection limits below 0.05 µg/L.

Sulfide and cyanide are toxic anions. Their trace determination in any kind of water samples, especially in wastewater, is requied for safety reasons. However, metal traces present in the eluent can mask target anions due to complexation. The addition of a stronger complexing agent to the eluent mask these metal cations enabling interference free determaination. This application is mainly used for the analysis of cyanide and/or sulfide in water. However, it also fulfills the requirements of ASTM D2036 for the determination of total, amenable, weak acid dissociable cyanides. The determination of cyanide and sulfide require an alkaline eluent and amperometric detection. This Application Note describes a new column/eluent combination for optimized separation. The combination consists of the Metrosep A Supp 10 - 100/4.0 column and a sodium hydroxide eluent containing a trace of EDTA for transition metal complexation. This yields in better peak shape and detection limits below 0.1 μg/L.

As a result of the private burning of wood, concentrations of levoglucosan, mannosan, and galactosan in the air are usually increased during the winter months. On the other hand, one can expect a greater contribution of sugar components from biogenic sources during the summer months. An optimum separation and sensitivity of the saccharide markers that accumulate on air filters can be achieved on the Metrosep Carb 2 - 150/4.0 column with subsequent pulsed amperometric detection.

Ion chromatographic determination of sulfide in wastewater is performed using amperometric detection and an alkali eluent to ensure the stability of the sulfide. Measurements are performed in single-potential or direct current (DC) amperometric mode. It is the best-known and most sensitive amperometric measuring method and also provides, in addition to a high selectivity, a large selection of working electrodes.Sulfide determination is performed on a Metrosep A Supp 10 - 100/4.0 type column; a silver electrode is used as the working electrode.

As a result of the private burning of wood, concentrations of levoglucosan, mannosan and galactosan in the air are usually increased during the winter months. By contrast, a greater contribution of sugar components originating from biogenic sources can be anticipated in the summer months. Optimum separation and sensitivity of the saccharide markers that collect on air filters are achieved on the Metrosep Carb 2 - 150/2.0 column with subsequent pulsed amperometric detection.

Cyanide in wastewater is an important parameter to measure for health requirements. Free, weakly complexed, and strongly complexed cyanide can be differentiated. Direct measurement in the wastewater is not feasible due to the matrix itself. Therefore, total cyanide is determined after acidification of the sample, which releases all cyanide from complexes, and subsequent distillation and absorption of cyanide in an alkaline solution. Amperometric detection is applied using a gold working electrode. This electrode is advantageous over the silver electrode due to less contamination issues and better long-term stability.

Gold leaching by cyanidation requires precise monitoring of cyanide and gold. Online process analyzers perform such measurements, improving safety and compliance.

Carbon capture systems strip carbon dioxide from flue gases. Online analysis of amines and carbon dioxide enhances amine usage efficiency and reduces operational costs.

This Process Application Note is dedicated to the online analysis of zinc, iron and sulfuric acid in several stages of the zinc production process. Additionally, traces of germanium, antimony, as well as several transition metals (e.g., Ni, Co, Cu, Cd) can be precisely determined (<50 µg/L) in the purification filtrates and reactor trains.

This Process Application Note deals with online measurements of ammonia, nitrite, and nitrate in wastewater treatment plants. These nitrogen compounds are analyzed simultaneously using a drift-free colorimetric measurement in a multi-parameter process analyzer from Metrohm Process Analytics.

Chromium is extracted from chromite ore and is an important part in the production of stainless steel. Chromium is mainly divalent, trivalent and hexavalent in its compounds. In contrast to chromium(III), which is an important trace element and one that is only sparingly soluble in water, hexavalent chromium is extremely toxic and very water-soluble. Cr(VI) is furthermore an important raw material for industry. It must be determined rapidly and precisely in the lower µg/L range in wastewater. Metrohm Applikon offers an array of process analyzers for the analysis of wastewater streams which determine chromium precisely and reproducibly using photometry.

Phosphorus removal is essential in waste water treatment plants to ensure the environmental balance is not upset by discharged effluent. In the treatment facility it is important to know the bioavailable o-phosphate phosphorus (o-PO4-P) concentration in the influent stream either to feed bacteria or to calculate the amount of reagents needed for chemical treatment. For environmental compliance monitoring purposes, treated effluent is monitored for TP – the sum of all insoluble and dissolved phosphates present. With the Metrohm Process Analytics 2035 TP Analyzer (complete with integrated compact digestion cuvette photometer module), you can keep track of both o-PO4-P and TP according to DIN EN ISO 6878:2004-09 around the clock.

Drinking water which has been disinfected via the ozonation process can contain undesirable levels of bromate, a carcinogen, via oxidation of bromide in the raw water. Already several agencies including the World Health Organization have recommended concentration limits for bromate set in place to limit its risks to our health. Ion chromatography is mentioned in several analytical standards for the determination of disinfection byproducts (DBP) including bromate, such as EPA 300.1, 317.0, 321.8, 326.0, ASTM D6581, ISO 11206, and ISO 15061. Monitoring trace levels of bromate online means higher throughput and less time spent performing manual laboratory tests, and ensures quality drinking water is produced.

Incineration flue gas requires treatment such as wet scrubbing. The 2060 VA Process Analyzer monitors heavy metals in the scrubbing water, ensuring compliance.

Spectroelectrochemistry is a multi-response technique that provides both electrochemical and spectroscopic information about a chemical system in a single experiment, i.e., it offers information from two different points of view. Spectroelectrochemistry focused on the UV/VIS region is one of the most important combinations because this allows us to obtain not only valuable qualitative information, but also outstanding quantitative results. In this application note, the degradation kinetics for 4-nitrophenol, a known pollutant, were determined using SPELEC.

Many electrochemical methods have been developed but are traditionally limited to aqueous media. Raman spectroelectrochemistry in organic solutions is an interesting alternative, but developing new EC-SERS procedures is still required. This Application Note demonstrates that the electrochemical activation of gold and silver electrodes enables the detection of dyes and pesticides in organic media.

Determination of chloride, nitrate, phosphate, and sulfate in wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, bromide, nitrate, and sulfate in surface water using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in soil eluates using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, and sulfate in synthetic seawater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, formate, chloride, nitrite, bromide, nitrate, phosphate, and sulfate in process water using anion chromatography with conductivity detection after chemical suppression.

Determination of nitrite and nitrate in wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of 1 (3) µg/L of chloride, nitrite, bromide, nitrate, phosphate, and sulfate after direct injection using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, phosphate, and sulfate in surface water using anion chromatography with conductivity detection after chemical suppression; nitrite with electrochemical detection (conductivity and ELCD detectors in series).

Determination of sulfate in wastewater after nitric acid combustion using anion chromatography with conductivity detection after chemical suppression.

Determination of NTA, EDTA, and DTPA in surface water and wastewater using ion pair chromatography with UV-detection after post-column reaction with the MSM.

Determination of bromide and phosphate in waste dump drainage water in the presence of very high concentrations of other ions and organic substances using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in rainwater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, bromide, nitrate, sulfate, and iodide in rock leachant using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in dust using anion chromatography with conductivity detection after chemical suppression.Sample:dust sampleSample preparation:0.1 g of dust dissolved in 100 mL c(HNO3) = 0.02 mol/L 0.45 µm filtration